Guide

How to Put a Pod in a Nespresso Machine

Updated on · By the My Time For Me team

To put a pod in a Nespresso machine, open the brew head, seat the capsule the right way up for your model, and close it fully before pressing a button. Original machines take a small capsule in a lever-lift slot; Vertuo machines take a wider capsule that you lock under a rotating head.

On this page (8 sections)
  1. How do you load a pod in an Original Nespresso machine?
  2. How do you load a Vertuo pod?
  3. What's the difference between Original and Vertuo pod loading?
  4. How do you close the head without crushing the pod?
  5. Why won't the pod go in or stay seated?
  6. How do you brew and remove the pod after loading?
  7. Which Nespresso machines make pod loading easiest?
  8. What mistakes should you avoid when loading a pod?

To put a pod in a Nespresso machine, open the brew head, seat the capsule the right way up for your model, and close it fully before pressing a button. Original machines take a small capsule in a lever-lift slot; Vertuo machines take a wider capsule that you lock under a rotating head.

The two families look similar on the counter but load differently. Get the capsule orientation and the closing motion right and the machine pierces and brews without a struggle.

Force it and you risk a stuck pod or a leak.

How do you load a pod in an Original Nespresso machine?

Lift the lever, drop the capsule in flat side down, and press the lever down. Original machines such as the Essenza Mini use a hinged head over a small capsule chamber.

The lever opens the chamber, the capsule rests on its flat base, and closing the lever pushes it into place.

On the Essenza Mini the lever sits at the top front of the machine. Lift it fully so the chamber opens wide, then slide the capsule in flat side down.

The machine brews espresso and lungo, so the capsule size is fixed; anything wider simply won't seat. Those two cup sizes are programmable, so you set the volume once and then just tap the button for each brew.

Close the lever firmly until it stops. You'll feel the capsule being pierced as the head comes down.

Then press the espresso or lungo button.

The Essenza Mini heats up in about 25 seconds, so the wait after closing the lever is short. It also shuts itself off automatically to save energy, and it measures only 4.3 inches deep by 8 inches wide by 12.8 inches high.

That small footprint is why the capsule chamber is compact and why a capsule has to sit level before the lever will go down.

How do you load a Vertuo pod?

Open the head, set the wide capsule in the cup holder with the barcode ring facing the machine, and turn the head to lock. Vertuo capsules are larger and domed, with a printed code around the rim.

The machine reads that code as it spins the capsule during brewing.

On a Vertuo Pop+ you raise the head, place the capsule in the holder so the flat top faces up and the code ring sits at the base, then press the head down until it clicks. The machine heats in about 30 seconds according to Nespresso, then starts on its own.

The head reads the code and sets the cup size and brewing settings without you choosing a button.

Don't peel or pierce a Vertuo capsule. The machine does that itself once the head is locked.

The capsule is hermetically sealed to keep the ground coffee fresh, and that seal is part of what the machine opens at the right moment.

The Vertuo Pop+ holds a 25.4 fluid ounce water tank that sits on the side. Fill it before you load the capsule so the brew isn't interrupted by a refill.

The tank is removable, so you can carry it to the sink and click it back into place.

What's the difference between Original and Vertuo pod loading?

Original capsules drop into a small chamber under a lever; Vertuo capsules lock under a spinning head. The shapes are not interchangeable.

An Original capsule is a small, narrow cup; a Vertuo capsule is a wide dome with a code ring.

Original machines pierce the capsule from above and below. Vertuo machines spin the capsule and use Centrifusion technology to read the code and mix coffee with water.

That's part of how a Nespresso machine works, and it's why the loading step differs. The spinning motion is also what builds the layer of crema on top of a Vertuo coffee.

Check your capsule box before buying. Vertuo pods are labeled Vertuo; Original pods are labeled Original.

A pod that doesn't match your machine will not fit, no matter how you angle it. A Vertuo machine also brews five cup sizes, from espresso up to Alto and Cold Brew style coffee, so the capsule you pick decides the size rather than a separate button.

How do you close the head without crushing the pod?

Close it in one steady motion until it stops or clicks, and never slam it. The head is designed to pierce the capsule at a set depth.

Pushing harder than the mechanism allows can bend the capsule or jam the piercer.

If the head won't close all the way, stop. A capsule sitting at an angle or a stray piece of foil in the chamber will block it.

Open the head, lift out the capsule, check the chamber for debris, and try a fresh pod. A used capsule left in the chamber is a common culprit, because it dries out and sticks to the holder.

On Vertuo models the head turns rather than presses. Twist it until it locks; the capsule should feel snug, not crushed.

The click you feel is the head seating over the code ring, and the machine won't brew until that lock is complete.

Why won't the pod go in or stay seated?

The usual causes are the wrong capsule family, an upside-down pod, or an open chamber that isn't fully open. Check these before you force anything.

  1. Match the capsule to the machine: Vertuo pods for Vertuo machines, Original pods for Original machines.
  2. Turn the capsule so the flat side or code ring sits as the holder expects.
  3. Open the head fully so the holder is clear and level.
  4. Remove any foil, grounds or a stuck old capsule from the chamber.

If a capsule went in and the machine still won't brew, the problem may be the machine rather than the pod. Our guide to how to open a Nespresso machine covers a stuck head, and a reset can clear some brew faults; see how do I reset my Nespresso machine.

What does a capsule sitting wrong look like?

A capsule that isn't seated shows up in small ways. The head won't reach its stop, or it closes but feels loose.

On an Original machine the lever may stop short of flat. On a Vertuo machine the head may turn but not click.

Look into the holder before you close anything. The capsule should sit flat, centered and level.

If one edge rides up over the rim, lift it out and set it down again rather than pressing it down with the head.

How do you brew and remove the pod after loading?

Press the matching cup-size button, let the brew finish, then lift the head and tip the capsule into the used-pod bin. Don't open the head mid-brew; the pressure and spinning need the capsule locked.

On an Original machine, press espresso or lungo. On a Vertuo Pop+, the machine reads the capsule and picks the size, so you just close the head and wait.

A Vertuo Pop+ offers five cup sizes from espresso to Alto and Cold Brew style coffee, and the capsule code decides which one you get.

When the flow stops, wait a moment, then open the head. The capsule drops into the bin on many models.

Let it cool before you handle it, and empty the bin regularly so old pods don't block the next one. On the Essenza Mini the used capsule container sits under the brew head, so you lift the head and the spent pod falls in.

On Vertuo Pop+ models the bin works the same way.

If you brew a milk drink, the capsule still comes out the same way. The milk frother on the Vertuo Pop+ with Milk Frother works separately from the capsule, so you load and brew the coffee first, then froth milk alongside it.

Which Nespresso machines make pod loading easiest?

A lever-lift Original machine is the simplest to load, while a Vertuo Pop+ adds automatic size reading and milk frothing. Pick by the capsule family you want rather than by the loading step alone.

The Vertuo Pop+ with Milk Frother reads each capsule's code and brews five sizes, and the included frother handles lattes and cappuccinos. The frother is a separate unit from the machine, so you can froth milk while the coffee brews.

The Vertuo Pop+ by De'Longhi uses the same capsule-loading head without the frother. Both take only Vertuo capsules.

Both also share the same 14 inch depth, 8.6 inch width and 10.4 inch height, so neither takes more counter space than the other.

If you mostly drink espresso and lungo and want the fewest steps, the Original Essenza Mini is the easy pick. Its 1.3 pound capacity spec refers to the machine's small size, and the whole unit weighs 6 pounds, so it's light enough to move aside when you need the counter.

For more on how long these machines tend to serve you, see how long does a Nespresso machine last.

What mistakes should you avoid when loading a pod?

The costliest mistakes are forcing a capsule, using the wrong family, and reusing a pod. Each one can jam the machine or spoil the coffee.

  • Don't force a head that won't close. Find the blockage first.
  • Don't mix capsule families. Vertuo pods won't fit Original machines and the reverse is also true.
  • Don't reuse a capsule. It's pierced and spent after one brew.
  • Don't leave a pod in the chamber for days. Empty it after brewing so it doesn't dry out and stick.

Once you know how to put a pod in a Nespresso machine for your model, loading becomes a two-second habit. Open the head, seat the capsule correctly, close it firmly, and press the button.

Keep the capsule family straight and you'll rarely meet a stuck pod again.

For the full routine after brewing, our related guide covers cleaning and care so the head keeps closing smoothly.

Frequently asked questions

Can you use Original pods in a Vertuo machine?

No. Original capsules are small and pierced from above and below, while Vertuo capsules are wider and read by a code ring the machine spins.

Each capsule type only fits the machine family it was made for, so buy the matching pods.

Why won't my Nespresso pod go in all the way?

The capsule is probably upside down, too large for that slot, or the brew head isn't open fully. Check the capsule shape against the holder, lift or turn the head as far as it goes, and try a fresh capsule before forcing anything.

What should I do with a used Nespresso pod?

Let it cool, then tip it into the used-capsule bin built into many machines. Nespresso recycles the aluminium capsules through its free program, so empty them and collect them for drop-off or mail-back where that service runs.

Do you need to preheat before inserting a capsule?

No. Load the capsule first and let the machine heat as part of the brew.

A Vertuo Pop+ heats in about 30 seconds according to Nespresso, so you won't wait long after closing the head.