Guide

How to Descale a Nespresso Vertuo Next

Updated on · By the My Time For Me team

Run the Vertuo Next's built-in descaling cycle with fresh water and a Nespresso descaling solution, then run the rinse cycle twice before brewing again. The machine walks you through it: enter descaling mode, fill the tank, let the solution run through, empty the tank, and rinse.

On this page (10 sections)
  1. What you need before you start a Vertuo Next descale
  2. How to put the Vertuo Next into descaling mode
  3. Run the descaling cycle
  4. Empty the tank and start the first rinse
  5. Run the second rinse and finish
  6. How often should you descale the Vertuo Next?
  7. Common mistakes that make descaling harder
  8. When descaling doesn't fix the problem
  9. Where the Vertuo Next fits in the Vertuo lineup
  10. The short version of descaling a Vertuo Next machine

Here's how to descale a Nespresso Vertuo Next machine: run the built-in descaling cycle with fresh water and a Nespresso descaling solution, then run the rinse cycle twice before brewing again. The machine guides you through the steps with its lights, so you mostly fill the tank, press the button, and empty the used water.

Descale when the orange light comes on. Mineral scale builds up inside the brew path, and clearing it keeps the coffee tasting as it should.

The whole job takes about 20 to 30 minutes of mostly waiting.

What you need before you start a Vertuo Next descale

Gather a full tank of fresh water, a Nespresso descaling solution, a container for the used water, and a cloth. The Vertuo Next runs the cycle on its own once you enter descaling mode.

Clear the counter around the machine and put the empty container under the coffee outlet. It should hold at least the full water tank, because the used solution and rinse water come out there.

Keep a second container or a sink nearby so you can empty the tank without moving the machine far.

Eject any capsule and close the head. The lever stays locked during the cycle.

Unplugging the machine partway through cancels the job and leaves solution inside, so plan to finish in one sitting.

How to put the Vertuo Next into descaling mode

With the machine off, press and hold the coffee button until it blinks orange, then release. That entry sequence puts the Vertuo Next into its descaling cycle, and the lights change to show each step.

If the button won't enter descaling mode, check that the machine is fully cooled and that no capsule sits in the head. A head that isn't locked also keeps the cycle from starting.

Power the machine off, wait a moment, and try the hold again.

Once the orange light blinks, the machine is ready for the solution. Fill the tank to the top line with fresh water and add the descaling solution as the pack directs.

Stir it gently so the two mix evenly.

Run the descaling cycle

Press the coffee button once to start the solution running through the machine. The pump pushes it through the brew path and out the outlet, and the light blinks while it works.

Let the full tank empty into the container. The machine stops when the tank runs low.

When it does, empty the used solution container and rinse it, so the next step starts clean.

Don't top up the tank with more solution to "finish the job". The pack makes a set amount, so follow the directions on the pack.

Adding more solution only wastes it and makes the rinse longer.

If the cycle stops before the tank is empty, the water sensor may have tripped on a low level. Fill the tank and press the button to resume.

The machine remembers where it was.

Empty the tank and start the first rinse

Pour out any solution left in the tank and fill it with clean fresh water. The first rinse clears the descaling solution out of the brew path, and the machine runs it without a capsule.

Press the coffee button to run the rinse water through. Let the tank empty again.

The lights show the rinse in progress the same way they showed the descale.

Some owners top the tank up halfway through the rinse to stretch it. It's simpler to let it run to empty and refill.

A full tank of clean water gives the internals a proper flush.

Wipe the outlet area with the cloth once the rinse finishes. A little solution can collect around the spout, and a quick wipe keeps it off your cup rim next time.

Run the second rinse and finish

The Vertuo Next asks for a second rinse, and you should do it. A single rinse can leave a faint taste in the first coffee, so the second pass clears the rest of the solution.

Fill the tank to the top with fresh water again and press the coffee button. Let it run through to empty.

When the cycle is complete, the light turns steady green and the machine is ready.

Pull the drip tray and give it a rinse in the sink. Used solution can leave a film there.

Dry it, slide it back, and run a throwaway brew if you want to be sure the taste is clean.

Now the machine is descaled. The orange light stays off until scale builds up again.

Brew your next capsule as usual.

How often should you descale the Vertuo Next?

Follow the orange light, and expect a reminder every few months in typical water. Nespresso sets the descaling reminder around your water hardness and how many cups you brew.

Hard water leaves scale faster than soft water. If your tap water is hard, the light may come on sooner than a neighbor's with soft water.

Running filtered water in the tank slows the buildup and stretches the gap between descales.

Don't skip the light because the coffee still tastes fine. Scale builds quietly, and the first sign is often a slower pour or a cooler cup.

Clearing it early is easier than clearing a thick layer later.

If you brew several cups a day, the reminder arrives sooner. A household that makes two capsules a day descales more often than one that makes a cup on weekends.

The machine counts the cycles, so it tracks your use.

Common mistakes that make descaling harder

The most common slip is skipping the second rinse. A single pass leaves solution in the lines, and the next coffee carries a chemical edge that no capsule fixes.

Another is running the cycle with a capsule still in the head. The machine won't complete the job, and the capsule wastes.

Eject it first, every time.

Some people pour the solution straight into the tank without mixing it. The pack makes a set amount for one cycle.

Follow the mix on the pack, not a guess.

Don't interrupt the cycle to answer the door and leave it half done. Powering off mid-cycle traps solution inside.

Finish the descale and both rinses in one go.

When descaling doesn't fix the problem

If the coffee still pours slowly after a full descale and both rinses, the issue is likely the capsule or the machine, not scale. Try a fresh capsule and check that the head closes fully.

A machine that won't enter descaling mode or stops partway may need a reset. Power it off, unplug it for a minute, plug it back in and try the sequence again.

If it still won't run the cycle, contact Nespresso support.

Scale is only one cause of a weak brew. A clogged outlet or a capsule that isn't pierced properly can mimic the same symptom.

If you've just descaled, rule those out before assuming the machine is failing.

Where the Vertuo Next fits in the Vertuo lineup

The Vertuo Next uses the same descaling routine as other Vertuo machines, so the steps carry over. The button sequence differs slightly between models, but the cycle and the two rinses are the same idea.

If you're still deciding between models, our comparison of the Nespresso Vertuo vs Vertuo Next covers how the two handle maintenance and brewing. For the smaller Vertuo Pop, the descaling steps follow the same pattern but with its own button sequence.

Our guide to how to descale a Nespresso Vertuo Pop machine walks through that model.

If iced coffee is your main use, the machine you choose matters more than the descale routine. Our roundup of the best Nespresso machine for iced coffee compares the options.

And if you're wondering whether a Vertuo can brew original pods, the answer is in our guide to whether a Nespresso Vertuo can use original pods.

The short version of descaling a Vertuo Next machine

Enter descaling mode with the machine off and the coffee button held, run the solution through, empty the tank, then rinse twice. Fresh water and a Nespresso solution are the only supplies the cycle needs, and the machine handles the rest.

The orange light is your cue, not a calendar. When it comes on, set aside half an hour, clear the counter, and run the full cycle in one sitting.

Skipping the second rinse is the one shortcut that costs you a clean-tasting first cup.

If you keep up with the light, the Vertuo Next stays easy to live with. For the supplies, use a Nespresso descaling solution made for the machine and a container that holds a full tank.

Then brew your next capsule without worrying about scale.

Frequently asked questions

Can I use vinegar instead of Nespresso descaling solution?

No. Vinegar is not approved for the Vertuo Next and can leave an odor and taste in the brew path.

Use Nespresso's own descaling solution, which is made for the machine's internal parts.

What do the orange and green lights mean during descaling?

The orange light tells you the machine needs descaling. During the cycle the lights change to show each step, and the green light returns when the process is finished and the machine is ready.

How long does descaling a Vertuo Next take?

Plan on about 20 to 30 minutes for the descaling cycle and the two rinses, plus a few minutes to empty and refill the water tank between steps. The machine pauses between steps, so you don't have to stand over it.

Do I need to remove the capsule before descaling?

Yes. Eject any capsule first so the machine is empty, then close the head and leave the lever locked.

A capsule left in place blocks the cycle and can make the machine stop partway through.

Can I brew coffee during the descaling cycle?

No. The machine locks out brewing while it is in descaling mode.

Wait until the full cycle and both rinses are finished and the green light is steady before you brew a capsule.